AIRTRONICS M12 Uživatelská příručka Strana 10

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 116
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 9
10

 
The M12 is equipped with several different Audible Warning Alarms to warn you of an abnormal transmitter condition. In addition,
LED1, LED2 and the R-MODE LED are used to indicate various transmitter conditions at a glance.
Inactivity (Power ON) Alarm:
The Inactivity Alarm will sound if the transmitter is Left on for a period of 10 minutes without any control input from the user. This
alarm alerts you to prevent unwanted draining of the transmitter battery. To clear this alarm, either turn the transmitter OFF or
press the BACK key or the ENTER key.
Over Voltage Alarm:
The Over Voltage Alarm will sound if the transmitter battery voltage is greater than 9.6 volts. To clear this alarm, turn the transmitter
OFF and replace the transmitter battery with one that when fully charged does not exceed 9.6 volts.
Low Voltage Alert Alarm:
The Low Voltage Alert alarm will sound when the transmitter batteries reach the Low Voltage Alert alarm voltage value
programmed in the SYSTEM - BATTERY menu. The alarm will sound each time the transmitter battery voltage decreases by 0.1
volt. To clear this alarm, press the BACK key or the ENTER key.
Low Voltage Limit Alarm:
The Low Voltage Limit alarm will sound when the transmitter batteries reach the Low Voltage Limit alarm voltage value
programmed in the SYSTEM - BATTERY menu. This alarm can only be cleared by turning the transmitter OFF and recharging or
replacing the transmitter batteries.


LED1, LED2 and the R-MODE LED are used to indicate various transmitter conditions at a glance. Some of the conditions indi-
cated by the LEDs may also be accompanied by an audible alarm and/or and on-screen warning.
------
------
------
------
------
------
------
------
------
------
------
------
------
OFF
OFF
OFF
Green
Magenta
Cyan
Yellow
White
OFF
------
------
------
------
------
------
0.1 Sec. Flash
0.1 Sec. Flash
OFF
ON
0.35 Sec. Flash
0.05 Sec. Flash
0.05 Sec. Flash
1 Sec. Flash
1 Sec. Flash
------
------
------
------
------
------
------
OFF
ON
0.1 Sec. Flash
0.5 Sec. Flash
0.35 Sec. Flash
0.05 Sec. Flash
------
------
------
------
------
------
------
1 Sec. Flash
------
------
------
------
------
------
------
------
TRANSMITTER STATUS
LED1 CONDITION
R-MODE LED CONDITION
Display Mode
RF Output Signal
Throttle Offset Function Active
Telemetry Logger Function Active
RF Binding - Sending Bind Code
PC-Link USB Send/Receive Active
Inactivity Alarm Active
Telemetry Alarm Active
Telemetry Connection Active
No Telemetry Connection
Low Voltage Alert Alarm Active
Low Voltage Limit Alarm Active
Over Voltage Alarm Active
Transmitter Error
Programming Data/Update Error
Unrecoverable Update Error
Racing Mode 1 Active
Racing Mode 2 Active
Racing Mode 3 Active
Racing Mode 4 Active
Racing Mode 5 Active
Racing Mode Function Inhibited
LED2 CONDITION
------ Indicates HOLD Condition. LED May Be ON or OFF Depending on Other Specific Conditions
The audible alarms listed below may also be accompanied by an on-screen warning.
Zobrazit stránku 9
1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 115 116

Komentáře k této Příručce

Žádné komentáře