AIRTRONICS M12 Uživatelská příručka stáhnout pdf (Strana 76)













Turning Separate Functions ON and OFF:

When Racing Mode is turned ON (R-MODE > ACT), various functions can be programmed the same for all five Racing Modes or

they can be programmed independently, allowing you to have different function Programming Values for each of the five Racing

Modes. For example, with D/R

ST set to ON, you can choose a Dual Rate Steering percentage value of 100% for Racing Mode 1, a

Dual Rate Steering percentage value of 90% for Racing Mode 2 and so on.

1) From within the R-MODE menu, scroll UP or DOWN to highlight desired

function you would like to turn ON or OFF.

2) Press the ENTER key, then scroll UP or DOWN to choose the desired value,

either ON or OFF. When set to ON, you will be able to choose different

function Programming Values for each Racing Mode. When set to OFF,

function Programming Values will be the same for all Racing Modes.

SEPARATE functions setting range is OFF and ON. The default setting for all functions is OFF.

3) Press the ENTER key, then repeat steps 1 and 2 to change any other desired values.

Switching Racing Modes to Program Separate Functions:

If you've chosen to program one or more Racing Mode functions separately (as

described above), a Racing Mode Icon will be displayed within the specific

function Programming Menu to indicate which Racing Mode you're currently

programming the function for.

To program different values for each Racing Mode, make sure to switch to the desired Racing Mode first. For example, with

SEPARATE D/RST set to ON, open the D/R menu. An R1, R2, R3, R4 or R5 Racing Mode Icon will be displayed next to the Steering

function, depending on which current Racing Mode is Active.

Use the Racing Mode Switch (Trim Switch Trm4) to switch to Racing Mode 1. R1 will be displayed next to the ST > 100%

percentage value. Choose the desired Steering Dual Rate percentage value for Racing Mode 1, then press Trim Switch Trm4 to

switch to Racing Mode 2. R2 will be displayed next to the ST > 100% percentage value. Choose the desired Steering Dual Rate

percentage value for Racing Mode 2. While you're driving, you can now switch to different Dual Rate settings simply by switching

Racing Modes.

The Racing Mode Icon will only be displayed for Programming Menus within the RACING menu and only if the specific

function's Separate value is set to ON in the R-MODE menu. If no Racing Mode Icon is displayed, the function Programming

Value will be the same regardless of which Racing Mode is currently Active.















The Dual Rate function allows you to change the control authority of the Steering, Throttle High Side and Throttle Brake Side by

changing the amount of servo travel relative to control input. For example, by Increasing the Steering Dual Rate, you can make

the Steering servo travel more which might prevent your Model from pushing during turns. If your Model oversteers during turns,

you can reduce the amount of Steering Dual Rate.

IMPORTANT: Prior to programming the Dual Rate function, you should adjust the maximum Left and Right (or High and Low)

End Points. For more information, see the

EPA Menu

section on page 62.

In the default configuration, Trim Switch Trm3 controls Steering Dual Rate and

Trim Switch Trm5 controls Brake Dual Rate. Throttle Dual Rate can be changed

while you're driving by Assigning the Dual Rate function to another Trim Switch

or the Auxiliary Dial. For more information, see the

ASSIGN Menu

section on

pages 33 ~ 38.

Current Steering, Throttle and Brake Dual

Rate percentage values are displayed in the

Lower Right corner of the STATUS screen.

1 2 ... 71 72 73 74 75 76 77 78 79 80 81 ... 115 116

Komentáře k této Příručce

Žádné komentáře

AIRTRONICS M12 Uživatelská příručka Strana 76

Komentáře k této Příručce

Související produkty a manuály pro Dálková ovládání AIRTRONICS M12